Search

Search Criteria

 
 
 
 

Products meeting the search criteria

Sort By:  
Low voltage Integrated Servo Motor, 750W DC servo motor
View
integrated RS485 servo motor
$490.00
Low voltage Integrated Servo Motor, NEMA24 size DC servo motor
View
integrated dc servo motor
$310.00
Low voltage Integrated Servo Motor, RS485 serial DC servo Motor
View
RS485 servo motor
$200.00
Low voltage Integrated Servo Motor, 750W DC servo motor (AIS57,60,86)

RS485 integrated servo motor, Low voltage servo Motor, 750W DC servo Motor.

Integrated Servo Motor, DC Servo Motor with Customized Cable:

ItemSpecifications
Winding connection modeStar connection
Encoder type17bit absolute encoder
Shaft Radial Play0.025mm
Radial clearance0.06mm@450g
Axial clearance0.08mm@450g
Maximum radial bearing force15N@20MM   Start with the flange
Maximum radial axial force10N
Insulation gradeB Grade
Dielectric strength500VAC /minute
insulation resistanceMinimum 100Ω, 500VDC


Motor Parameters

    Model Number80AIS112
    Rated voltage(V)DC48V
    Rated power(W)750
    Rated current(A)18
    Rated torque(N. M)2.4
    Peak torque(N. M)4.8
    Rated speed(RPM)3000 ±10%
    Max speed(RPM)3200 ±10%
    Cable resistance(Ω)0.08 ±10%
    Cable inductance(MH)0.24 ±10%
    Torque coefficient(NM/A)0.12 ±10%
    Length(MM)112
    Pole5
    Level of protectionIp65
    Motor insulation classClass F


    Mechanical Dimensions and Wiring Diagram:

    Port Definition

    　TerminalNameDescription
    　1DCDC48V 
    2GNDGround
    　1D01Output Terminal 1Function depends on the user' setting
    2D01-
    3D02Output Terminal 2
    4D02-
    8DI1Input Terminal 1
    5DI2Input Terminal 2
    6DI3Input Terminal 3
    7DI_COMThe common terminal of the input terminal,
    Used to drive the input optocoupler,
    Connect DC12-24V (common positive NPN connection) or OV (common negative PNP connection)
    Current>100mA
    9DIRDirection Control Signal InputDC5-24V
    10DIR-
    11PULSPulse Control Signal Input
    12PULS-

    　S/NNameDescription
    CN6

    　    		1485A/TRS485
    2NCReserved
    3485B/TRS485 -
    4NCReserved
    5GNDGround
    6NCReserved
    7NCReserved
    8NCReserved
    　CN7
    		1485A/TRS485
    2NCReserved
    3485B/TRS485 -
    4NCReserved
    5GNDGround
    6SWCLK/TProgram upgrade clock line
    73.3Vcommunication 3.3V power supply
    8SWDIO/TProgram upgrade data line



    input powerThe allowed input voltage of different models of AIMotor motor is not consistent. Please see the motor specifications for details
    Dc power input, pay attention to the positive and negative electrodes of the power supply
    operating environmenttemperatureWorking: 0℃ ~ 55℃ Storage: -20℃ ~ 80℃
    humidityLess than 90% (no condensation)
    control method① position control ② speed control ③ torque control ④ communication control
    control characteristicSpeed frequency response: ≥200Hz
    Velocity fluctuation: < ±0.03 (load 0 ~ 100%) : < ±0.02×(0.9 ~ 1.1) supply voltage
    Receiving pulse frequency ≤100kHz
    control input01, servo enable; 02, alarm clearance; 03, multi-segment enable; 04, multi-segment select 1; 05, many paragraphs choose 2; 06, forward overrange; 07, reverse overrange; 08, positive turn point; 09, reverse point movement; 10. Origin switch 11, origin enable; 12. Emergency shutdown; 13. Pulse prohibition; 14. Remove
    position deviation;
    Control output01, the servo is ready to output; 02. Complete the output of positioning; 03, fault alarm output 04. Confirm the origin back to zero output;   05, electrical confirmation back to zero output; 06, torque to the output; 07, the
    speed reaches the output;
    position controlPulse mode: pulse direction; A plus B orthogonal pulse
    The electronic gear ratio defaults to 131072:1000, that is, 1000 pulses per turn
    Maximum pulse receiving frequency <=100KHZ
    Internal 4 section position mode: 1. Single cycle operation; 2, automatic cycle operation; 3. Multi-segment DI
    switch operation
    Communication control mode: RS485 Modbus_Rtu controls the corresponding communication location and
    address
    speed controlInternal 4 speed mode: 1, single cycle operation; 2, automatic cycle operation; 3. Multi-speed DI switching
    operation
    Communication control mode: RS485 Modbus_Rtu controls the corresponding communication speed address
    torque controlCommunication control mode: RS485 Modbus_Rtu controls the corresponding communication torque address
    Acceleration and
    deceleration function    		The time of ACC/DEC：1～65535 ms（0 r/min ～ 1000 r/min）
    Monitor functionCurrent speed, DI input, DO output, current position, command input pulse accumulation, average load rate, position deviation count, motor phase current, bus voltage value, module temperature, alarm record, command
    pulse frequency corresponding speed, running state, etc
    protect functionvervoltage and undervoltage of the main power supply, overspeed, overcurrent, overload, abnormal encoder,
    abnormal position, blocked rotation, abnormal parameters, etc
    Return to origin function13 autonomous (search) ways to return to the origin, as well as the origin offset function.
    RS485 functionIt follows the standard ModBUS-RTU protocol
    One point two communication interface, convenient network parallel
    gain adjustmentManually adjust
    Internal rigidity grade table adjustment


    Connect to many slave stations via PLC device,  with Simens S7-200Smart as an example:


    Host computer debugs a connection:


    AIS series Integrated DC Servo Motor Software #ADMotor works well in PC, please download software

    AIS Series RS485 Integrated Servo Motor User Manual 

    More Information on detail, please feel free to contact me  

    View
    integrated RS485 servo motor
    $490.00
    Low voltage Integrated Servo Motor, NEMA24 size DC servo motor (AIS57,60,86)

    RS485 integrated servo motor, Low voltage servo Motor, NEMA24 size DC servo Motor.


    ItemSpecifications
    Winding connection modeStar connection
    Encoder type17bit absolute encoder
    Shaft Radial Play0.025mm
    Radial clearance0.06mm@450g
    Axial clearance0.08mm@450g
    Maximum radial bearing force15N@20MM   Start with the flange
    Maximum radial axial force10N
    Insulation gradeB Grade
    Dielectric strength500VAC /minute
    insulation resistanceMinimum 100Ω, 500VDC


    Motor Parameters

      Model Number60AIS9560AIS113
      Rated voltage(V)DC24VDC48V
      Rated power(W)200400
      Rated current(A)1211
      Rated torque(N. M)0.641.27
      Peak torque(N. M)1.273.82
      Rated speed(RPM)3000 ±10%3000 ±10%
      Max speed(RPM)3200 ±10%3200 ±10%
      Cable resistance(Ω)0.12 ±10%0.27 ±10%
      Cable inductance(MH)0.36 ±10%0.56 ±10%
      Torque coefficient(NM/A)0.06 ±10%0.12 ±10%
      Length(MM)95113
      Pole5
      Level of protectionIp54
      Motor insulation classClass F


      Mechanical Dimensions and Wiring Diagram:

      Port Definition

      　TerminalNameDescription
      　1DCDC24-36V
      2GNDGround
      　1D01Output Terminal 1Function depends on the user' setting
      2D01-
      3D02Output Terminal 2
      4D02-
      8DI1Input Terminal 1
      5DI2Input Terminal 2
      6DI3Input Terminal 3
      7DI_COMThe common terminal of the input terminal,
      Used to drive the input optocoupler,
      Connect DC12-24V (common positive NPN connection) or OV (common negative PNP connection)
      Current>100mA
      9DIRDirection Control Signal InputDC5-24V
      10DIR-
      11PULSPulse Control Signal Input
      12PULS-

      　S/NNameDescription
      CN6

      　      		1485A/TRS485
      2NCReserved
      3485B/TRS485 -
      4NCReserved
      5GNDGround
      6NCReserved
      7NCReserved
      8NCReserved
      　CN7
      		1485A/TRS485
      2NCReserved
      3485B/TRS485 -
      4NCReserved
      5GNDGround
      6SWCLK/TProgram upgrade clock line
      73.3Vcommunication 3.3V power supply
      8SWDIO/TProgram upgrade data line



      input powerThe allowed input voltage of different models of AIMotor motor is not consistent. Please see the motor specifications for details
      Dc power input, pay attention to the positive and negative electrodes of the power supply
      operating environmenttemperatureWorking: 0℃ ~ 55℃ Storage: -20℃ ~ 80℃
      humidityLess than 90% (no condensation)
      control method① position control ② speed control ③ torque control ④ communication control
      control characteristicSpeed frequency response: ≥200Hz
      Velocity fluctuation: < ±0.03 (load 0 ~ 100%) : < ±0.02×(0.9 ~ 1.1) supply voltage
      Receiving pulse frequency ≤100kHz
      control input01, servo enable; 02, alarm clearance; 03, multi-segment enable; 04, multi-segment select 1; 05, many paragraphs choose 2; 06, forward overrange; 07, reverse overrange; 08, positive turn point; 09, reverse point movement; 10. Origin switch 11, origin enable; 12. Emergency shutdown; 13. Pulse prohibition; 14. Remove
      position deviation;
      Control output01, the servo is ready to output; 02. Complete the output of positioning; 03, fault alarm output 04. Confirm the origin back to zero output;   05, electrical confirmation back to zero output; 06, torque to the output; 07, the
      speed reaches the output;
      position controlPulse mode: pulse direction; A plus B orthogonal pulse
      The electronic gear ratio defaults to 131072:1000, that is, 1000 pulses per turn
      Maximum pulse receiving frequency <=100KHZ
      Internal 4 section position mode: 1. Single cycle operation; 2, automatic cycle operation; 3. Multi-segment DI
      switch operation
      Communication control mode: RS485 Modbus_Rtu controls the corresponding communication location and
      address
      speed controlInternal 4 speed mode: 1, single cycle operation; 2, automatic cycle operation; 3. Multi-speed DI switching
      operation
      Communication control mode: RS485 Modbus_Rtu controls the corresponding communication speed address
      torque controlCommunication control mode: RS485 Modbus_Rtu controls the corresponding communication torque address
      Acceleration and
      deceleration function      		The time of ACC/DEC：1～65535 ms（0 r/min ～ 1000 r/min）
      Monitor functionCurrent speed, DI input, DO output, current position, command input pulse accumulation, average load rate, position deviation count, motor phase current, bus voltage value, module temperature, alarm record, command
      pulse frequency corresponding speed, running state, etc
      protect functionvervoltage and undervoltage of the main power supply, overspeed, overcurrent, overload, abnormal encoder,
      abnormal position, blocked rotation, abnormal parameters, etc
      Return to origin function13 autonomous (search) ways to return to the origin, as well as the origin offset function.
      RS485 functionIt follows the standard ModBUS-RTU protocol
      One point two communication interface, convenient network parallel
      gain adjustmentManually adjust
      Internal rigidity grade table adjustment


      Connect to many slave stations via PLC device,  with Simens S7-200Smart as an example:


      Host computer debugs a connection:


      AIS series Integrated DC Servo Motor Software #ADMotor works well in PC, please download software

      AIS Series RS485 Integrated Servo Motor User Manual 

      More Information on detail, please feel free to contact me  

      View
      integrated dc servo motor
      $310.00
      Low voltage Integrated Servo Motor, RS485 serial DC servo Motor (AIS57,60,86)

      RS485 integrated servo motor, Low voltage servo Motor, NEMA23 size DC servo Motor.

      Integrated Servo Motor, Low Voltage DC servo Motor With Cutomized Cable:


      ItemSpecifications
      Winding connection modeStar connection
      Encoder type17bit absolute encoder
      Shaft Radial Play0.025mm
      Radial clearance0.06mm@450g
      Axial clearance0.08mm@450g
      Maximum radial bearing force15N@20MM   Start with the flange
      Maximum radial axial force10N
      Insulation gradeB Grade
      Dielectric strength500VAC /minute
      insulation resistanceMinimum 100Ω, 500VDC


      Motor Parameters

        Model Number57AIS6157AIS7757AIS100
        Rated voltage(V)DC24VDC24VDC24V
        Rated power(W)326085
        Rated current(A)1.92.96.2
        Rated torque(N. M)0.480.631.45
        Peak torque(N. M)0.720.952.18
        Rated speed(RPM)1200 ±10%1000 ±10%1100 ±10%
        Max speed(RPM)1800 ±10%1700 ±10%2100 ±10%
        Cable resistance(Ω)2.73 ±10%1.52 ±10%0.73 ±10%
        Cable inductance(MH)1.15 ±20%0.62 ±20%0.27 ±20%
        Torque coefficient(NM/A)0.1350.1320.115
        Electrical time constant(MS)0.4210.4080.37
        Length(MM)6177100
        Pole14
        Level of protectionIp65
        Motor insulation classClass F


        Mechanical Dimensions and Wiring Diagram:

        Port Definition

        　TerminalNameDescription
        　1DCDC24-36V
        2GNDGround
        　1D01Output Terminal 1Function depends on the user' setting
        2D01-
        3D02Output Terminal 2
        4D02-
        8DI1Input Terminal 1
        5DI2Input Terminal 2
        6DI3Input Terminal 3
        7DI_COMThe common terminal of the input terminal,
        Used to drive the input optocoupler,
        Connect DC12-24V (common positive NPN connection) or OV (common negative PNP connection)
        Current>100mA
        9DIRDirection Control Signal InputDC5-24V
        10DIR-
        11PULSPulse Control Signal Input
        12PULS-

        　TerminalNameDescription
        　CN6
        		1485A/TRS485
        2NCReserved
        3485B/TRS485 -
        4NCReserved
        5GNDGround
        6NCReserved
        　CN7
        		1485A/TRS485
        2SWCLK/TProgram upgrade clock line
        3485B/TRS485 -
        4SWDIO/TProgram upgrade data line
        5GNDGround
        63.3Vcommunication 3.3V power supply



        input powerThe allowed input voltage of different models of AIMotor motor is not consistent. Please see the motor specifications for details
        Dc power input, pay attention to the positive and negative electrodes of the power supply
        operating environmenttemperatureWorking: 0℃ ~ 55℃ Storage: -20℃ ~ 80℃
        humidityLess than 90% (no condensation)
        control method① position control ② speed control ③ torque control ④ communication control
        control characteristicSpeed frequency response: ≥200Hz
        Velocity fluctuation: < ±0.03 (load 0 ~ 100%) : < ±0.02×(0.9 ~ 1.1) supply voltage
        Receiving pulse frequency ≤100kHz
        control input01, servo enable; 02, alarm clearance; 03, multi-segment enable; 04, multi-segment select 1; 05, many paragraphs choose 2; 06, forward overrange; 07, reverse overrange; 08, positive turn point; 09, reverse point movement; 10. Origin switch 11, origin enable; 12. Emergency shutdown; 13. Pulse prohibition; 14. Remove
        position deviation;
        Control output01, the servo is ready to output; 02. Complete the output of positioning; 03, fault alarm output 04. Confirm the origin back to zero output;   05, electrical confirmation back to zero output; 06, torque to the output; 07, the
        speed reaches the output;
        position controlPulse mode: pulse direction; A plus B orthogonal pulse
        The electronic gear ratio defaults to 131072:1000, that is, 1000 pulses per turn
        Maximum pulse receiving frequency <=100KHZ
        Internal 4 section position mode: 1. Single cycle operation; 2, automatic cycle operation; 3. Multi-segment DI
        switch operation
        Communication control mode: RS485 Modbus_Rtu controls the corresponding communication location and
        address
        speed controlInternal 4 speed mode: 1, single cycle operation; 2, automatic cycle operation; 3. Multi-speed DI switching
        operation
        Communication control mode: RS485 Modbus_Rtu controls the corresponding communication speed address
        torque controlCommunication control mode: RS485 Modbus_Rtu controls the corresponding communication torque address
        Acceleration and
        deceleration function        		The time of ACC/DEC：1～65535 ms（0 r/min ～ 1000 r/min）
        Monitor functionCurrent speed, DI input, DO output, current position, command input pulse accumulation, average load rate, position deviation count, motor phase current, bus voltage value, module temperature, alarm record, command
        pulse frequency corresponding speed, running state, etc
        protect functionvervoltage and undervoltage of the main power supply, overspeed, overcurrent, overload, abnormal encoder,
        abnormal position, blocked rotation, abnormal parameters, etc
        Return to origin function13 autonomous (search) ways to return to the origin, as well as the origin offset function.
        RS485 functionIt follows the standard ModBUS-RTU protocol
        One point two communication interface, convenient network parallel
        gain adjustmentManually adjust
        Internal rigidity grade table adjustment


        Connect to many slave stations via PLC device,  with Simens S7-200Smart as an example:


        Host computer debugs a connection:


        AIS series Integrated DC Servo Motor Software #ADMotor works well in PC, please download software

        AIS Series RS485 Integrated Servo Motor User Manual 

        More Information on detail, please feel free to contact me  

        View
        RS485 servo motor
        $200.00
        Per Page      1 - 3 of 3
        • 1